Clarke Crocodile Circular Saw Kit, Model# CT5000
Posted on | September 3, 2010 | 2 Comments
From the Manufacturer
Handheld Crocodile circular saw kit cuts a variety of material, including metals, plywood, ceramic tile, marble, drywall, conduit and more.
Handheld Crocodile circular saw kit cuts a variety of material, including metals, plywood, ceramic tile, marble, drywall, conduit and more.
Tags: ceramic tile > conduit > Crocodile > drywall > Kit > kit model > marble > material > Metals > Model > Plywood > Saw > tile marble
Delta 35-7646 10″ 60 Tooth Fine Crosscut Circular Saw Blade (+10 Hook)
Posted on | September 2, 2010 | No Comments
From the Manufacturer
Delta 35-7646 10″ 60 Tooth Fine Crosscut Circular Saw Blade (+10 Hook)
Forrest MM09802 Miter Master 9-Inch 80 Tooth 5/8-Inch Arbor .105-Inch Kerf Aluminum Cutting Circular Saw Blade
Posted on | September 1, 2010 | No Comments
The Forrest MM09802 Circular Saw Blade is an all-purpose blade for table saws that leaves edges ready to use with minimal planing and sanding. The Forest MM09802 Blade is double hard for a longer cutting life and made for cutting thin, low pressure, two-sided laminates, plywood & fine cross cutting on all woods between 1- and 2-inches thick.
From the Manufacturer
Forrest’s blades offer a superior cut that leaves a rip-cut saw edge that is as smooth as if it had been sanded, and a cross-cut edge that is almost mark-free. The blades run very quietly, and backside tearout in plywood is negligible. Each blade is virtually hand-made. The plate is hand-tensioned (up to 15 minutes per blade), superior C-4 c (more…)
Tags: 15 minutes > Aluminum > backside > circular saw blade > cross cut > edge > Kerf > Plywood > pressure > Saw > table > table saws > Tooth
DEWALT DW378GT Heavy-Duty Framer 15 Amp 7-1/4-Inch Hyphoid Circular Saw
Posted on | August 31, 2010 | No Comments
Manufacturer’s Notice
The U.S. Consumer Product Safety Commission, in cooperation with the firm named below, today announced a voluntary recall of the following consumer product. Consumers should stop using recalled products immediately unless otherwise instructed. Name of Product: DeWalt DW378G/DW378GT Framing Saws and DC300 Circular Saws. Units: About 97,000 framing saws and 37,000 circular saws. Manufacturer: DeWalt Industrial Tool Co., of Towson, Md. Hazard: The lower blade guard can fail to close, leaving the blade exposed and presenting a laceration hazard to consumers. Incidents/Injuries: DeWalt has received four reports of the lower guard failing to close, including three reports of lacerations. One consumer received (more…)
Tags: circular saws > consumer product safety > consumer product safety commission > Duty > firm > Framer > framing saws > Hazard > laceration hazard > Product > product consumers > product safety commission > Safety > Saw
Forrest MM10807 Miter Master 10-Inch 80 Tooth 5/8-Inch Arbor .105-Inch Kerf Aluminum & Wood Circular Saw Blade
Posted on | August 30, 2010 | No Comments
From the Manufacturer
Forrest’s blades offer a superior cut that leaves a rip-cut saw edge that is as smooth as if it had been sanded, and a cross-cut edge that is almost mark-free. The blades run very quietly, and backside tearout in plywood is negligible. Each blade is virtually hand-made. The plate is hand-tensioned (up to 15 minutes per blade), superior C-4 carbide teeth are hand-brazed to the plate, and the blade is straightened and restraightened multiple times throughout the process. Think of a Forrest blade as a tool in your shop, not an accessory. Forrest stands behind it’s blades by offering a sharpening service that bring blades back to the exact tolerances offered in a new blade. And this same exacting service (more…)
Tags: backside > Blade > carbide teeth > circular saw blade > cross cut > edge > exact tolerances > exacting service > Kerf > plate > Saw > sharpening service > wood
-
Top 10 Circular Saw
Top 10 Circular Saw
